PDA

Показать полную графическую версию : помогите разогнать атлон 1700+


Страниц : 1 [2]

Tuma123
28-03-2008, 15:59
так, нашёл : Albatron KX18DS PROII(два) К1.01
http://www.organizator.ru/id/24229/detailed.html - вот она!

$ancho$
28-03-2008, 22:16
Tuma123, значит с платой определились? Если так, то давай потихоньку разгонять. Award BIOS. Заходишь в BIOS Setup -> раздел Chipset Features Setup -> Ищи опцию FSB:SDRAM:PCI Freq. Ratio ставишь там [133:100:33]. Затем ищи опцию FSB/SDRAM/PCI Freq. - вот это значение надо потихоньку повышать. Если таких параметров у тебя нет, ищи с подобными названиями (FSB, Frequency и т.п.) и выкладывай сюда. Еще лучше зайди в этот раздел, сфоткай монитор и снимок в студию, а то мы так долго не разберемся.

yurfed
28-03-2008, 23:25
$ancho$, нашёл я мануал ftp://ftp.albatron.com.tw/FAE/Manual/Mainboard/KX18_Series/KX18DS_Pro-KX18DS_ProII/KX18DS_EM_N1.pdf (1.5МБ)
:)
Tuma123, память какая стоит?

yurfed
28-03-2008, 23:51
Выкладываю основное, на случай если не получится скачать. У меня после пива башка не варит :)
Скопировал с PDF. На знаки вопроса не обращаем внимания, а редактировать лень.
Надеюсь и так всё понятно.

KX18DS PRO/ KX18DS PRO II
Advanced Chipset Features
System Performance
This item allows you select the system performance which you want.
Options: Optimal (default) Use the most stable settings
Aggressive/Turbo Use over clocked settings for higher performance but with higher risk
of instability
Expert Allows full customization of performance options. Advanced user only.

FSB Frequency
This item allows you to select the CPU Frequency. The mainboard can detect the CPU Frequency as
long as the BIOS can identify the ID number for the CPU you have installed. Otherwise the CPU
Frequency will be set to safe values that you can manually adjust in the item hen . W the “System
Performance” set to “Expert” the options range will be 100 ~ 300 MHz.

CPU Interface
When the “System Performance” set to “Expert”, this item allows you to set the CPU/FSB
parameters.
Options: Optimal Use most stable CPU/FSB parameters
Aggressive Use overclocked CPU/FSB parameters

DDR:CPU Ratio
When the “System Performance” set to “Expert”, this item allows you to adjust your “DDR:CPU
Ratio” and overclock the DDR speeds of the system.
Options: 1?1.2?1.33?1.50?1.60?1.66?2?2.4?2.5?2.66?3?3.33?4?Auto or AUTO,
BySPD (default)

DDR Speed (Strobe/Sec)
This item shows the DDR Speed.


Memory Timings
When the “System Performance” set to “Expert”, this item allows you to select the memory timing.
This item determines DRAM clock/ timing using SPD or manual configuration. Make sure your
memory module has SPD (Serial Presence Data), if you want to select the “Optimal”.
Options: Optimal (default)?Aggressive?Turbo?Expert

T (RAS)
When the “Memory Timings” set to “Expert” then the item allows you to select DRAM active to
Precharges Delay. Row-active delay => set system performance to “Optimal” to use the delay
recommend by the DIMM’s manufacturer. Options: 1~15

T (RCD)
When the “Memo im ” set to “Expert” then the item allows you to select the DRAM delay ry T ings
time when begin read. RAS-to-CAS delay => set system performance to “Optimal” to use the delay
recommend by the DIMM’s manufacturer.Options: 1~7

T (RP)
When the “Memory Timings” set to “Expert” then the item allows you to set the time to precharge.
Row-precharge delay => set system performance to “Optimal” to use the delay recommend by the
DIMM’s manufacturer. Options: 1~7

CAS Latency Time
This item determines CAS Latency. When synchronous DRAM is installed, the number of clock
cycles of CAS laten depends on the DRAM timing. cy Do not reset this field from the default value
specifie by the system engineer. This field is adjustable on d ly when “Memory Timing” is set to
“Aggressive”. Options: 2.5?3 and By SPD (default)

Memory Auto Precharge
This item allows you to enable or disable the memory auto precharge.
Options: Disabled (default)?Enabled

AGP Frequency
This item allows you to select the AGP frequency.
Options: Auto (default)?50 MHz?66~87 MHz?90 MHz?93 MHz?95 MHz?97 MHz?100 MHz


PCI Latency Timer (CLK)
This item allows you to set up the PCI Latency Time (0-255). If you select the “32” it will optimize
PCI speeds. Options: 0-255?32 (default)

Frequency/ Voltage Control
CPU Speed Detected
This item displays the CPU Speed.

CPU Clock Ratio
This field allows you to adjust the CPU clock ratio. When the CPU clock ratio is locked by the CPU
manufacturer, you will not be able to adjust this field.
Options: Available options will depend on the CPU installed.

Default CPU Voltage (Volt)
This item displays the CPU default Voltage.

CPU Voltage (Volt)
This item allows you to adjust your CPU core voltage.

AGP Voltage (Volt)
This item allows you to adjust the AGP Voltage. Options: 1.5 (default)?1.6?1.7?1.8

DDR Voltage (Volt)
This item allows you to adjust the RAM voltage.
Options: 2.70 (default)?2.80?2.90?3.00

Chipset Voltage (Volt)
This item allows you to adjust the North/ South bridge chipsets voltage.
Options: 1.6 (default)?1.7?1.8?1.9

$ancho$
29-03-2008, 13:37
Tuma123, yurfed притаранил мануал к твоей плате, за что ему спасибо ;) :
- Заходишь в Advanced Chipset Features
- Пункт System Performance - устанавливаешь Expert
- пункт CPU Clock Ratio - Что у тебя там есть?
- Пункт DDR:CPU Ratio - устанавливаешь 1.
- Пункт AGP Frequency - 66~87Mhz
- Пункт FSB Frequency - здесь начинаешь увеличивать значение. Далее все зависит от того, чего ты хочешь добиться: выжать все из своего бедолаги :) или просто немного повысить производительность с сохранением стабильности.
Если первое, то повышай это значение и напряжение в п. CPU Voltage (Volt) пока не упрешься в потолок - (:idea: Аккуратнее следи за температрой проца!!!).
Если второе, то увеличивай FSB понемногу с тестированием в программах-тестах и бенчмарках (OCCT, SuperPi, Prime95, 3DMark и море им подобных). Если все проходит нормально - повышай FSB еще, если - комп перезагружается, выскакивают синие экраны, то повышай напряжение CPU и снова тестируй. (Можно еще повысить Chipset Voltage (Volt) и DDR Voltage (Volt) - тоже самое следи за температурой мостов и памяти!!!) После разгона проца можно еще поиграться с таймингами памяти (если она приличная ;). Таким образом найдешь оптимальные параметры.
Кстати говоря
Tuma123, память какая стоит? »
Выяснил?

TAVVAT
29-03-2008, 15:46
Tuma123, К вышесказанному $ancho$, хочу добавить, что при разгоне процев Athlon нужно снизить частоту шины HyperTransport. Обычно достаточно установить множитель х3 или частоту 600 МГц(в зависимости от биоса), что одно и то же. (именно из за этого поначалу у меня были трудности с разгоном).
И еще добавлю что поначалу можно смело увеличить частоту FSB на 20, потом на 10 или 5 МГц. Меньший шаг нерационален.




© OSzone.net 2001-2012